SLH700

Cost-efficient force and mass measurement

The SLH700 strain transducer can endure rough environments, for example in silo weighing or structural monitoring tasks. Other typical applications are press monitoring, welding force measurement or force measurements in c frames.

SLH700

expand_more

chevron_left

chevron_right

Strain transducer SLH700 – Hermetically sealed and with minimal influence on the measured object allowing use for lower strain to force comparatives

Extensometers, such as the SLH700 series measure forces indirectly and are distinguished by their simple yet effective functionality. When a force is applied to the structure on which the sensor is mounted, deformations whose magnitude depends on the applied force, occur. Therefore, even large forces can be measured with economically once the SLH700 has been calibrated.

SLH700 strain links are made from stainless steel materials, are hermetically sealed and have a high degree of protection (IP68). Their cable is resistant to most oils and many other potentially aggressive fluids. The transducer is built as a strain transformer. Therefore, the output signal is six times that of the single strain gauge.

The SLH700 strain link series can be purchased with or without an integrated amplifier, providing a selection of analogue output signals. All variants have an extremely low force shunt and can easily be mounted, requiring only two standard M6 screws.

HBK accuracy class: 0.5
Nominal (rated) measurement ranges: 150 µm/m
Outputs: 1,5 mV/V, 0... 10 V, or 4... 20 mA, depending on variant
Degree of protection: up to IP68

Economic measurements

Inexpensive yet reliable – especially when measuring large forces
The SLH700VA with integrated electronics and standard analogue outputs provides a particularly cost-efficient solution

Cost advantages over other methods of force measurement, especially for large forces.

For monitoring or manufacturing tasks

Easy mounting with two M6 screws
Oil resistant and highly flexible cable, suitable for drag chains
High degree of protection (IP68); also suitable for permanent outdoor use

Robust and long-lasting force measurement even in unfavourable environmental conditions.

The complete package

HBK supplies the sensors required for the calibration of the SLH700 strain link
A service team can calibrate the measurement chain for you if required

Flexible for different applications

Extremely low restoring force
No impact on the stiffness of the system

The SLH700 is suitable for use on both large and delicate structures.

Code	出力信号	最低温度	最大温度	最低温度	最大温度
1-SLH700/06-1	mV/V (passive strain gauge), mV/V（パッシブひずみゲージ）	-30 °C	85 °C	-22 °F	185 °F
1-SLH700/06VA1-1	Voltage (0…10V), 電圧 (0…10V)	-20 °C	60 °C	-4 °F	140 °F
1-SLH700/06VA2-1	Current (4-20mA), 電流 (4-20mA)	-20 °C	60 °C	-4 °F	140 °F

SLH700 - データシート	Data Sheets	English
SLH700 - 設置マニュアル	Mounting Instructions	English, French, Chinese, German

SLH700 - CAD	CAD Step Files
SLH700VA with integrated electronics - CAD	CAD Step Files

SLH700
Type/technology	Strain Gauge
Capacity (strain)	500 μm/m
Capacity (strain)	500 μm/m
Output signal	Voltage (0…10V), mV/V (passive strain gauge), Current (4-20mA)
Degree of protection	IP68
Mechanical adaptation	Bolted
Minimum Temperature	-20 °C, -30 °C
Maximum Temperature	60 °C, 85 °C
Minimum Temperature	-4 °F, -22 °F
Maximum Temperature	140 °F, 185 °F

Main Menu

Main Menu

Main Menu

Main Menu

SLH700

Economic measurements

For monitoring or manufacturing tasks

The complete package

Flexible for different applications

Related Content

プレス荷重監視部品

PMX

CST

Force