arrow_back_ios

Main Menu

See All Software See All Instruments See All Transducers See All Vibration Testing Equipment See All Electroacoustics See All Acoustic End-of-Line Test Systems See All Academy See All Resource Center See All Applications See All Industries See All Services See All Support See All Our Business See All Our History See All Global Presence
arrow_back_ios

Main Menu

See All nCode - Durability and Fatigue Analysis See All ReliaSoft - Reliability Analysis and Management See All Test Data Management See All DAQ Software See All Drivers & API See All Utility See All Vibration Control See All High Precision and Calibration Systems See All DAQ Systems See All S&V Hand-held Devices See All Industrial Electronics See All Power Analyzer See All S&V Signal Conditioner See All Acoustic See All Current and Voltage Sensors See All Displacement See All Force sensors See All Load Cells See All Pressure See All Strain Gauges See All Temperature Sensors See All Torque Sensors See All Vibration See All Accessories for Vibration Testing Equipment See All Vibration Controllers See All Measurement Exciters See All Modal Exciters See All Power Amplifiers See All LDS Shaker Systems See All Test Solutions See All Actuators See All Combustion Engines See All Durability See All eDrive See All Production Testing Sensors See All Transmission & Gearboxes See All Turbo Charger See All Training Courses See All Acoustics See All Asset & Process Monitoring See All Custom Sensors See All Data Acquisition & Analysis See All Durability & Fatigue See All Electric Power Testing See All NVH See All Reliability See All Smart Sensors See All Vibration See All Weighing See All Automotive & Ground Transportation See All Calibration See All Installation, Maintenance & Repair See All Support Brüel & Kjær See All Release Notes See All Compliance See All BKSV Worldwide Contacts
arrow_back_ios

Main Menu

See All API See All Microphone Cartridges See All Microphone Sets See All Microphone Pre-amplifiers See All Sound Sources See All Acoustic Calibrators See All Special Microphones See All Accessories for acoustic transducers See All Experimental testing See All Transducer Manufacturing (OEM) See All Piezoelectric Charge Accelerometers See All Piezoelectric CCLD (IEPE) accelerometers See All Electroacoustics See All Noise Source Identification See All Environmental Noise See All Sound Power and Sound Pressure See All Noise Certification See All Industrial Process Control See All Structural Health Monitoring See All Electrical Devices Testing See All Electrical Systems Testing See All Grid Testing See All High-Voltage Testing See All Vibration Testing with Electrodynamic Shakers See All Structural Dynamics See All Machine Analysis and Diagnostics See All Dynamic Weighing See All Vehicle Electrification See All Calibration Services for Transducers See All Calibration Services for Handheld Instruments See All Calibration Services for Instruments & DAQ See All On-Site Calibration See All Resources See All Software License Management

Portable Data Recorder Measures Sand Grain Fracture after Explosions

University of Texas, United States of America

Introduction

HBK's Genesis HighSpeed data recorder was used for measuring acoustic emissions to understand the behaviour of sand grains during an explosion.

Challenge

A project sponsored by the Office of Naval Research wanted to understand the behavior of sand and its energy absorption in a blast to improve the design of armor.

 

Solution

Engineers used a Genesis HighSpeed DAQ equipped with an acoustic emission sensor to gather data which they correlated with the deformation of sand grains and the number of sand grains that fractured.

 

Result

This information helps engineers design better armor for military vehicles.

chevron_left
chevron_right

Bullets cannot penetrate sandbags, so understanding the behavior of granular material such as sand and its energy absorption in a blast is critical in the design of body armor for soldiers. To this end, as part of the "Soil Blast Modeling and Simulations" project, sponsored by the Office of Naval Research’s Multidisciplinary University Research Initiative (MURI), our lab performed hundreds of experiments using a portable data recorder to determine the mechanical behavior of grains of sand sliding against each other after explosions. 

The most effective way to understand this mechanical behavior is by studying sand’s acoustic emissions (AE) during a blast event. AEs are short lived, high frequency, elastic waves generated by the rapid release of stored energy. In this case, sliding friction and rolling between sand grains are the sources of AEs. Acoustic emissions carry real time information about the location, intensity, and deformation mechanisms occurring in a material.

Correlating AE Spikes with Deformations of Sand Grains

In our experiments, we acquired AE data using a Genesis HighSpeed portable data recorder from HBK. The company provides solutions for test and measurement applications such as sensors, transducers, strain gages, amplifiers, data recorders and data acquisition systems (DAQ), and structural durability analysis software.

We first put sand into a hollow cylinder and placed an acoustic emission sensor (a piezoelectric-based device that transforms the pressure wave into an electrical signal) at the boundary of the material. The AE sensor was attached to a charge amplifier, which output a voltage that was fed to the Genesis.

To replicate blast forces, we used a cylindrical rod to push on the sand and apply compression. The applied pressure caused the grains to deform until some grains actually fractured. The AE events that resulted were sub-micron to mm in size, giving rise to signals with frequencies in the range of 10 kHz to several MHz.

We also compressed the outside of the cylinder and used a strain gauge attached to the data recorder to measure lateral deformation for additional AE data. We connected the strain gauge to the Genesis using a Wheatstone bridge powered by 10 volts DC. The signal was magnified by a signal amplifier. The voltage from the signal amplifier was converted through the Genesis via another circuit. Even at a fast data sampling rate of 10 MS/s, the data recorder readings were accurate and high-resolution. The recorder’s built-in 10x amplifier/conditioner signal conditioners also helped ensure high-quality data.

Next, we correlated the AE spikes in frequency shown on the Genesis with the deformation of sand grains and the number of sand grains that fractured. The events proved to have two entirely different signatures. Sand grains sliding against each other caused a low-frequency wave and low amplitude of sound, while grain fracture caused a high-frequency wave and high-amplitude acoustic wave.

Signal Processing

Signal processing, such as computing the energy of the acoustic emission source, provided information about the processes and mechanisms of deformation. In this case, we wrote special code to capture the data, saved the data onto a USB drive and then ran it on a computer in mathematical software to count the number of grains that fractured. This information helped us infer the magnitude of the blast. Basically, the data about AE signal frequencies and sand particle fracture rates told us what kind of blasts sand can forestall.

The Genesis HighSpeed data recorder, unlike other systems, is an integrated electronic device that does not require the use of a separate computer. The entire package weighs only 25 pounds, which makes it easier to carry from one location to another than other data recorders. Although the unit is small, it provides up to 96 fully configurable input ports. A large, easy-to-read and intuitive user interface makes it easy to select the desired data recording mode — continuous recording or triggered sweeps. Our team supplied the information we gathered from our experiments to another project team.

The team then used the data to simulate explosions on a computer to better understand how blast waves interact with sand and how they further propagate to potentially hit soldiers and their vehicles. The upshot is the processed information from Genesis proves useful to design engineers developing body armor for military personnel.

Author of this article

Hongbing Lu
Professor & Associate Department Head for Graduate Program
Louis A. Beecherl Jr. Chair
Department of Mechanical Engineering
The University of Texas at Dallas

University of Texas in Dallas 

More about the Department of Mechanical Engineering

Technology used