arrow_back_ios

Main Menu

arrow_back_ios

Main Menu

arrow_back_ios

Main Menu

PACEline CLP

PACEline CLP piezoelectric force washers fit virtually anywhere due to their minimal height of typically 4 mm.

img

PACEline CLP

expand_more
chevron_left
chevron_right

PACEline CLP Piezoelectric Subminiature Load Washer: Capacities From 3 kN to 80 kN

PACEline CLP piezoelectric load washers have a very low height of 3 to 5 mm. The sensors enable force to be measured at locations where standard force sensors cannot be installed. The sensors have an integrated cable (either 0.5 or 1 m long) and are a cost-effective way to allow for piezoelectric measurements to be taken.

By combining CLP load washers with different mounting directions of at least two CSW load washers, very small measurement systems can be set up to measure forces in different directions simultaneously.

  • Capacities: 3 kN to 80 kN
  • HBM accuracy class: 1

Fit for all standard screw connections ranging from M2.5 to M14

The piezoelectric miniature force washers of the PACEline CLP series are now available in three new capacities (3 kN, 14 kN, and 36 kN). This means for you that PACEline CLP is now available for all industry-standard screw connections ranging from M2.5 to M14. The tiny force sensors can be installed in very small setups, without the need to resize or adapt the screw or bolt connections.

Minimal space required

  • 3 mm (CLP/3KN) to 5 mm (CLP/80 KN) height
  • 12 mm and 36 mm outside diameter
  • Also for use under difficult EMC conditions
  • Robust due to stainless steel materials and IP65 degree of protection (i.a. through integrated cable with different lengths)

Absolutely reliable force measurement, even where space is a constraint. 

Dynamic and wide measurement range

  • Fundamental frequencies in the kHz range due to extremely stiff design
  • All sensors of the CLP family have the same sensitivity
  • Low drift and high quality
  • The output signal depends only on the type of installation and the force applied.

ONE sensor for a huge measurement range - from a few Newtons to several kilo-Newtons. 

Well-thought-through accessories

  • Industry tried and tested charge amplifiers - even with higher IP65 degree of protection
  • Summing boxes and amplifiers are galvanically isolated from the test object to which they are installed
  • Wide choice of low-noise cables and extension adapters, available in practical lengths and with plugs suitable for the charge amplifier

Perfect accessories allow for fast installation of your measurement system. No additional insulation washers required for installation (due to galvanic isolation)

Filter

close
PACEline CLP - Data Sheet Data Sheets English
CLP - Mounting Instructions Mounting Instructions English, Italian, French, German

Certificates and Approvals

CFT/CFT+/CFW/CLP/CSW/CST/CHW - EU Declaration of Conformity Declaration of Conformity English
PACEline CLP
Maximum capacity (nominal load) 26 kN, 7 kN, 3 kN, 62 kN, 80 kN, 36 kN, 14 kN
Maximum capacity (nominal load) 5.85 klbf, 15.7 klbf, 674 lbf, 13.9 klbf, 18 klbf, 1.57 klbf, 89 klbf, 3.15 klbf
Direction Compression
Type / technology Piezoelectric
Calibration Not calibrated
Output signal pC (passive piezoelectric)
HBK Accuracy class 1
Load cell design Miniature sensor
Degree of protection IP65
Mechanical adaptation Force washer
Height (without accessories) 3.5 mm, 3 mm, 4 mm, 5 mm
Height (without accessories) 0.138 in, 0.118 in, 0.157 in, 0.197 in
Diameter (without cable or plug) 9.8 mm, 5.5 mm, 4.05 mm, 13.8 mm, 15.8 mm, 11.8 mm, 7.8 mm
Diameter (without cable or plug) 0.385826 in, 0.216535 in, 0.1594485 in, 0.543306 in, 0.622046 in, 0.464566 in, 0.307086 in